Mods
Listen
TS-9 Gain on 0
TS-9 Gain on 2.5
TS-9 Gain on 5
TS-9 Gain Maxed
BD-2 Gain on 0
BD-2 Gain on 2.5
BD-2 Gain on 5
BD-2 Gain on7.5
BD-2 Gain maxed
DS-1Gain on 0 Switch on
DS-1Gain on 2.5
DS-1 Gain on 5 Switch on
DS-1 Gain on 7.5 Switch on
DS-1 Gain maxed Switch on
TS-9 and 808 Custom mod
A chip upgrade and resistor and cap upgrades make the tube screamer come alive and sound amazing. Changes are made to the drive circuit to allow full control on the drive knob with the potential for much more drive while maintaining a clean boost when on 0. Changes are made to the tone circuit for improved low-end response as well as input circuit changes for improved input signal transfer. A true bypass switch is optional on the TS-9 and 808 to eliminate tone sucking.
A chip upgrade and resistor and cap upgrades make the tube screamer come alive and sound amazing. Changes are made to the drive circuit to allow full control on the drive knob with the potential for much more drive while maintaining a clean boost when on 0. Changes are made to the tone circuit for improved low-end response as well as input circuit changes for improved input signal transfer. A true bypass switch is optional on the TS-9 and 808 to eliminate tone sucking.
Boss BD-2 Blues Driver mod
Upgrades to coupling and bypass capacitors greatly improve input to output transparency, as well as low to mid-range frequency response. Diode changes on the drive circuit for better and smoother asymmetrical clipping and harmonics. Huge improvement to tone control circuit, which makes it fully usable and functional, therefore providing a wider range for tone shaping. Add an optional deep switch for switching between 2 different levels of bass boost.
Upgrades to coupling and bypass capacitors greatly improve input to output transparency, as well as low to mid-range frequency response. Diode changes on the drive circuit for better and smoother asymmetrical clipping and harmonics. Huge improvement to tone control circuit, which makes it fully usable and functional, therefore providing a wider range for tone shaping. Add an optional deep switch for switching between 2 different levels of bass boost.
Boss DS-1 Distortion Custom mod
Several Hi-Fi mods are made by upgrading a number of capacitors resulting in smoother gain and clarity, as well as more bass and mid-range response. We install a distortion toggle switch to the drive circuit to switch between a 1N4002 diode and an LED providing various gain levels and sustain that's endless with a wide range of rich smooth tones
Several Hi-Fi mods are made by upgrading a number of capacitors resulting in smoother gain and clarity, as well as more bass and mid-range response. We install a distortion toggle switch to the drive circuit to switch between a 1N4002 diode and an LED providing various gain levels and sustain that's endless with a wide range of rich smooth tones
Boss SD-1 Super Overdrive Custom Mod
We perform a chip upgrade as well as capacitor and resistor upgrades that give you more drive, nicer harmonics, improved base response and clarity. An optional two-way gain switch added to the clipping section that allows you to select between two different levels of gain and drive.
We perform a chip upgrade as well as capacitor and resistor upgrades that give you more drive, nicer harmonics, improved base response and clarity. An optional two-way gain switch added to the clipping section that allows you to select between two different levels of gain and drive.
Boss TR-2 Tremolo Custom Mod
Installation of an adjustable output level to fix the volume drop when the effect is on. Also, add an optional external volume control and turn the TR-2 into a nice preamp/gain booster by turning the depth all the way down and the volume up on the tremolo. We add a rate LED as well for visual observation of rate and speed.
Installation of an adjustable output level to fix the volume drop when the effect is on. Also, add an optional external volume control and turn the TR-2 into a nice preamp/gain booster by turning the depth all the way down and the volume up on the tremolo. We add a rate LED as well for visual observation of rate and speed.
Boss GE-7 Equalizer Custom Mod
Upgrades are made to higher quality op-amp chips and capacitors to reduce noise and provide a clearer more focused tone to the circuit. Noise is substantially reduced and the signal is completely transparent, preserving the original tone of the guitar.
Upgrades are made to higher quality op-amp chips and capacitors to reduce noise and provide a clearer more focused tone to the circuit. Noise is substantially reduced and the signal is completely transparent, preserving the original tone of the guitar.
Boss CS-3 Compressor Custom Mod
We replace a number of Capacitors, Diodes and resistors to hi quality components. We swap out IC chips to less noisy high quality IC's. Collectively this changes the output resulting in a concise, clear transparent and distinct sound from the noisy, muddied up sound of the stock unit.
We replace a number of Capacitors, Diodes and resistors to hi quality components. We swap out IC chips to less noisy high quality IC's. Collectively this changes the output resulting in a concise, clear transparent and distinct sound from the noisy, muddied up sound of the stock unit.
Boss DD2, DD3 and DD5 Custom Mod
This is a high cut mod, installing a 3 way toggle switch which cuts the highs of the delay and each repeat, giving the delay a very warm analog feel while preserving the stock sound in the middle position.
This is a high cut mod, installing a 3 way toggle switch which cuts the highs of the delay and each repeat, giving the delay a very warm analog feel while preserving the stock sound in the middle position.
Hi fi mods are performed by swapping out a number of capacitors for top quality metal film capacitors to reduce the background hiss. Most noticeable when the guitar isn't being played. Also reduces the boxy sound and ads more depth to the flanger
Wah Custom Mods
Changes to component quality and values for smoother sweep and better gain control as well as improved, more vocal Wah tones. Also 100% true bypass to eliminate tone sucking and an LED indicator to indicate when the Wah is on. Add a DC Jack for external power supply on the Vox Wah. Optional mods include external volume/mid control, which adjusts the level of volume and mid-range and a 3 way bass select switch to select between 3 different bass levels. Also add an output buffer to allow for full range in to a high impedance dirt pedal.
Changes to component quality and values for smoother sweep and better gain control as well as improved, more vocal Wah tones. Also 100% true bypass to eliminate tone sucking and an LED indicator to indicate when the Wah is on. Add a DC Jack for external power supply on the Vox Wah. Optional mods include external volume/mid control, which adjusts the level of volume and mid-range and a 3 way bass select switch to select between 3 different bass levels. Also add an output buffer to allow for full range in to a high impedance dirt pedal.
Note: Prices are subject to change without notice
Currently, we can mod Your: Dunlop GCB95, Dunlop Hendrix JH1, Dunlop Hendrix JH1-B, Dunlop Zakk Wylde, Vox V-847, Vox V-847A, Vox V848 Clyde McCoy and Jen Wah.
Boss BF-2 Custom Mod
For more information or to order pedals and mods, contact us at: info@customguitartone.com or call us at: 905-877-5160
We mod your own pedal to the custom mod.
For best results, right click on link and open in new window
Whammy 4 Mods
True Bypass:
We install a high quality bypass switch, Bright blue LED and replace the original bypass switch with a smaller, heavy-duty, high quality pushbutton switch. The pushbutton is necessary in case you need to re-calibrate your Whammy.
Preset LED Replacement:
We will install preset LED’s with colors of your choice to identify each preset with its own color. Specify both the Color and the Whammy setting.
first LED $12.00. Each additional is $6.00
Remote Foot Controller:
We will install a remote jack and build an external foot pedal to control the Whammy settings remotely with your foot.
Check it out on Utube
True Bypass:
We install a high quality bypass switch, Bright blue LED and replace the original bypass switch with a smaller, heavy-duty, high quality pushbutton switch. The pushbutton is necessary in case you need to re-calibrate your Whammy.
Preset LED Replacement:
We will install preset LED’s with colors of your choice to identify each preset with its own color. Specify both the Color and the Whammy setting.
first LED $12.00. Each additional is $6.00
Remote Foot Controller:
We will install a remote jack and build an external foot pedal to control the Whammy settings remotely with your foot.
Check it out on Utube